| Author | Post |
|---|
rwsandman007
Member
| Joined: | Fri Jan 26th, 2007 |
| Location: | |
| Posts: | 1 |
| Mana: |  |
|
Posted: Fri Jan 26th, 2007 08:37 pm |
|
| I have a 7.5 hp gamefisher outboard. I have no idea what year it is. How can I figure out what year it is? Anyways back to my question. The air/fuel mixture screw, how many turns out from the totally seated position? The carb is all screwed up and is adjusted all crazy. I need a starting point. Thankx
|
richoj
Member
| Joined: | Sun Oct 28th, 2007 |
| Location: | |
| Posts: | 2 |
| Mana: | |
|
Posted: Mon Oct 29th, 2007 07:51 pm |
|
| I have a Gamefisher 9.9 manual (1983 motor) which tells how to adjust the carb. If you care to provide an email address, I will send you a scan of the page. You start out at midpoint, etc.
|
frank54166
Member
| Joined: | Fri Feb 29th, 2008 |
| Location: | |
| Posts: | 10 |
| Mana: | |
|
Posted: Sun Mar 23rd, 2008 12:29 pm |
|
| check out sanfordsgoodies.com
|
kaydogs9
Member
| Joined: | Sun Aug 10th, 2008 |
| Location: | |
| Posts: | 1 |
| Mana: | |
|
Posted: Sun Aug 10th, 2008 06:54 pm |
|
hello. im very surprised to see or hear of anoth 7.5 gamefisher. i too have one.shes a good engine sofar.i have adjusted mine only slightly.when in neutral i turned it a 16 th to the right then a couple 16ths to the left until i got a good idle then dropped it in gear to see if i had a nice purr for trolling at 1.9 mph. engine notices when i dont get my oil to gas mixture correct. 50:1 premium murcury 2 cycle.seems to make her the happiest. although what brings me to this site was it just spits out a spray out of the pee hole. not sure im saying it right. but the jets about 5 inches above the water line. was thinking maybe its not working perfectly ( like a steady cylindrical stream of water)
does your water come out nice? they said the engine would overheat if it wasnt working right , but i have had it stop or freeze.
shes attached to an 12` foot alluminum and goes around 19 mph . but i added a swival chair and now only get 17.9mph .
sorry im long winded. i know that the screw you speak of can only be adjusted slightly in one direction or the other before its obviously in a bad setting.somewhere in the middle like that guy said.
i appeciate and imput. and good luck with your gamefisher. kyle romund 952-292-6751
|
frank54166
Member
| Joined: | Fri Feb 29th, 2008 |
| Location: | |
| Posts: | 10 |
| Mana: | |
|
Posted: Thu Aug 14th, 2008 05:05 pm |
|
frank54166 wrote: check out sanfordsgoodies.com lots of eska,ted williams,gamefisher,clinton,seaking,force and chrysler parts
|
frank54166
Member
| Joined: | Fri Feb 29th, 2008 |
| Location: | |
| Posts: | 10 |
| Mana: | |
|
Posted: Thu Aug 14th, 2008 05:07 pm |
|
| 1 1/4 turns out as a start point,you may have other problems if it only runs for a few seconds
|
Current time is 03:41 am | |
|
